2.6. Expressions

Expressions in NASM are similar in syntax to those in C.

NASM does not guarantee the size of the integers used to evaluate expressions at compile time: since NASM can compile and run on 64-bit systems quite happily, don’t assume that expressions are evaluated in 32-bit registers and so try to make deliberate use of ((integer overflow)). It might not always work. The only thing NASM will guarantee is what’s guaranteed by ANSI C: you always have at least 32 bits to work in.

NASM supports two special tokens in expressions, allowing calculations to involve the current assembly position: the $ and $$ tokens. $ evaluates to the assembly position at the beginning of the line containing the expression; so you can code an infinite loop using JMP $. $$ evaluates to the beginning of the current section; so you can tell how far into the section you are by using ($-$$).

The arithmetic operators provided by NASM are listed here, in increasing order of precedence.

2.6.1. |: Bitwise OR Operator

The | operator gives a bitwise OR, exactly as performed by the OR machine instruction. Bitwise OR is the lowest-priority arithmetic operator supported by NASM.

2.6.2. ^: Bitwise XOR Operator

^ provides the bitwise XOR operation.

2.6.3. &: Bitwise AND Operator

& provides the bitwise AND operation.

2.6.4. << and >>: Bit Shift Operators

<< gives a bit-shift to the left, just as it does in C. So 5<<3 evaluates to 5 times 8, or 40. >> gives a bit-shift to the right; in NASM, such a shift is always unsigned, so that the bits shifted in from the left-hand end are filled with zero rather than a sign-extension of the previous highest bit.

2.6.5. + and -: Addition and Subtraction Operators

The + and - operators do perfectly ordinary addition and subtraction.

2.6.6. *, /, //, % and %%: Multiplication and Division

* is the multiplication operator. / and // are both division operators: / is unsigned division and // is signed division. Similarly, % and %% provide unsigned and signed modulo operators respectively.

NASM, like ANSI C, provides no guarantees about the sensible operation of the signed modulo operator.

Since the % character is used extensively by the macro preprocessor, you should ensure that both the signed and unsigned modulo operators are followed by white space wherever they appear.

2.6.7. Unary Operators: +, -, ~ and SEG

The highest-priority operators in NASM’s expression grammar are those which only apply to one argument. - negates its operand, + does nothing (it’s provided for symmetry with -), ~ computes the one’s complement of its operand, and SEG provides the segment address of its operand (explained in more detail in Раздел 2.6.8).

2.6.8. SEG and WRT

When writing large 16-bit programs, which must be split into multiple segments, it is often necessary to be able to refer to the segment part of the address of a symbol. NASM supports the SEG operator to perform this function.

The SEG operator returns the preferred segment base of a symbol, defined as the segment base relative to which the offset of the symbol makes sense. So the code

        mov ax, seg symbol
        mov es, ax
        mov bx, symbol

will load es:bx with a valid pointer to the symbol symbol.

Things can be more complex than this: since 16-bit segments and groups may overlap, you might occasionally want to refer to some symbol using a different segment base from the preferred one. NASM lets you do this, by the use of the WRT (With Reference To) keyword. So you can do things like

        mov ax, weird_seg       ; weird_seg is a segment base
        mov es, ax
        mov bx, symbol wrt weird_seg

to load es:bx with a different, but functionally equivalent, pointer to the symbol symbol.

NASM supports far (inter-segment) calls and jumps by means of the syntax call segment:offset, where segment and offset both represent immediate values. So to call a far procedure, you could code either of

        call (seg procedure):procedure
        call weird_seg:(procedure wrt weird_seg)

(The parentheses are included for clarity, to show the intended parsing of the above instructions. They are not necessary in practice.)

NASM supports the syntax call far procedure as a synonym for the first of the above usages. JMP works identically to CALL in these examples.

To declare a far pointer to a data item in a data segment, you must code

        dw symbol, seg symbol

NASM supports no convenient synonym for this, though you can always invent one using the macro processor.